Home Page
|
Terms & Conditions
|
View Basket Contents
|
Go to the Checkout
|
Contact Us
We value your feedback
Click here to make suggestions
Spray Contact Adhesive - 25 Litres
Construction Chemicals Spray Contact Adhesive is a sprayable, high heat-resistant contact adhesive exhibiting fast solvent flash off and a long open tack time.
It demonstrates excellent adhesion to a wide range of substrates such as wood, decorative laminates, polyurethane foam, elastomers, plastics and metals.
In particular, the excellent hot bond strength of Construction Chemicals Spray Contact Adhesive makes it suitable for the post-forming of decorative laminates onto chipboard and MDF cores, using a wide range of static and continuous post-forming equipment e.g. Evans Rotork, Brandt Static, Bonding Systems. The high heat resistance of this product (up to 90 deg c) makes it ideal in most shop fitting situations.
APPLICATION
Surfaces to be bonded should be clean, dry and free from loose particles, dust and grease. Construction Chemicals Spray Contact Adhesive may be sprayed hot or cold. Hot spraying gives better atomisation, better coverage and faster solvent evaporation. In conditions of high humidity, hot spraying will prevent a ‘bloom’ forming on the adhesive surface, which would lead to poor bonds being made.
Construction Chemicals Spray Contact Adhesive may be sprayed through most equipment, but for best results, a Devilbiss JGV-562 gun fitted with FX fluid tip and needle, and a 777 air-cap is recommended. Atomising pressures of 70-90 psi and fluid pressures of 10-15 psi are required.
Apply an even coat of adhesive to both surfaces to be bonded. Allow a minimum of 2 minutes before mating surfaces.
Ensure intimate contact and coalescence of the adhesive films by passing the laminate through nip rollers or by platen pressing, using as much pressure as possible without crushing the components. Sustained pressure is not necessary. The high initial strength of the adhesive allows panels to be handled immediately.
SPECIAL COMMENTS
1. Construction Chemicals Spray Contact Adhesive is normally tinted red for easy observation of coverage but can be supplied in neutral or tinted in other colours on request.
2. Bonds are resistant to moisture, dilute acids and alkalis and many oils (non-aromatic types).
3. Store at temperatures above 4ºC (40ºF). Prolonged storage at lower temperatures may cause the formation of a ‘gel’ which will then necessitate re-processing.
4. Construction Chemicals Spray Contact Adhesive should only be sprayed on to polystyrene foam when adequate air is available (volume of 23 cfm and pressures of at least 70 psi) or, when hot sprayed, through recommended equipment.
5. In conditions of high humidity, a ‘bloom’ may form on the surface which reduces tack and coalescence. Bonds should not be made when this occurs.
The above figures do not constitute a specification. They represent typical values obtained for this product.
HEALTH AND SAFETY
Before using this product, ensure that you have been supplied with and have read carefully the following information:
· The hazard label (complying with CHIP Regulations) applied to the container
· Construction Chemicals Material Safety Data Sheet for this product
Construction Chemicals Spray Contact Adhesive is Highly Inflammable with a Flash Point below 23ºC. A licence is currently required under the Petroleum (Mixtures) Order 1929.
Construction chemicals Spray Contact adhesive has a current Warrington fire certificate for use where fire proof products are specified.
TECHNICAL DATA
Base Polychloroprene
Solids 20 ± 2%
Viscosity 150 – 250 cP at 20ºC
Colour Neutral or tinted
Tack life 2 – 45 minutes
Coverage 8 – 10m²/litre
Cleaner Solvent 1
Flash Point -18ºC
Shelf Life 12 months at 4 – 25ºC
Spray Contact Adhesive Health & Safety & Technical Data Sheet
Price:
£86.52
excluding VAT
Quantity:
1.
Oxalic Acid
Size - prices exclude VAT
25 kg - £75.00
5 kg - £25.00
Quantity:
2.
Envirosafe One Shot Injection Cream (DPC)
Size (prices exclude VAT)
5 Litres - £62.00
2 * 5 Litres - £61.00 each
5 * 5 Litres - £55.00 each
1 * 1 Litre - £15.60
6 * 1 Litre - £15.40 each
12 * 1 Litre - £15.00 each
380cc cartridge - £9.50
5 * 380cc cartridges - £7.85 each
10 * 380cc cartridges - £7.10 each
Quantity:
3.
Tanking Slurry - 25kg
Price:
£45.00
excluding VAT
Quantity:
4.
Wood Weld PU - 310ml
Number of Cartridges (prices exclude VAT)
One (£6.50)
Box of 12 (£4.98 per cartridge)
5 Boxes of 12 (£4.50 per cartridge)
11 Boxes of 12 (£4.00 per cartridge)
Quantity:
